72 lines
3.1 KiB
Plaintext
72 lines
3.1 KiB
Plaintext
## Rename to <app>.subdomain.conf, copy to SWAG's /config/nginx/proxy-confs/,
|
|
## validate, reload.
|
|
##
|
|
## The subdomain has to exist before this does anything: add <app> to SWAG's
|
|
## SUBDOMAINS (or run it with a wildcard cert) and point the DNS record at the
|
|
## same address as the rest of the stack. See docs/Install Server.md.
|
|
|
|
## Per-IP throttle for the login endpoints, if the app has a password. Declared
|
|
## here at `http` scope — SWAG includes proxy-confs outside any server block,
|
|
## which is what makes this legal in this file. 1 MB of zone holds about 16,000
|
|
## addresses. Delete both this and the `location` below if there is no login.
|
|
limit_req_zone $binary_remote_addr zone=app_login:1m rate=6r/m;
|
|
|
|
server {
|
|
listen 443 ssl;
|
|
listen [::]:443 ssl;
|
|
|
|
server_name app.example.com;
|
|
|
|
include /config/nginx/ssl.conf;
|
|
# Put proxy defaults at server scope so location timeouts override them
|
|
# through inheritance, rather than duplicate directives from proxy.conf.
|
|
include /config/nginx/proxy.conf;
|
|
|
|
# nginx buffers a request body to disk before it hands it on, and the login
|
|
# takes one without a session, so no limit here lets anyone spool gigabytes.
|
|
# This is small. A route that takes a large upload gets its own
|
|
# `location = /path { client_max_body_size 0; proxy_request_buffering off;
|
|
# ... }` above `location /`, with the same proxy lines as below; streaming
|
|
# the body lets the app refuse a request without a session before nginx
|
|
# has stored any of it.
|
|
client_max_body_size 1m;
|
|
|
|
# Guessing the password is already pointless if the app locks out after a
|
|
# handful of wrong answers (see auth/README.md). This is the
|
|
# cheap half of the rest: attempts are slowed per address, at the proxy,
|
|
# before they reach the app at all. `burst=5 nodelay` lets a person who
|
|
# fat-fingers it a few times through immediately and then holds the rate.
|
|
# `/login/passkey/options` is open and writes a challenge row per call, so
|
|
# it is throttled with the two routes that check a credential.
|
|
location ~ ^/login(/passkey(/options)?)?$ {
|
|
limit_req zone=app_login burst=5 nodelay;
|
|
limit_req_status 429;
|
|
|
|
include /config/nginx/resolver.conf;
|
|
set $upstream_app app;
|
|
set $upstream_port 8787;
|
|
set $upstream_proto http;
|
|
proxy_pass $upstream_proto://$upstream_app:$upstream_port;
|
|
}
|
|
|
|
location / {
|
|
include /config/nginx/resolver.conf;
|
|
|
|
set $upstream_app app;
|
|
set $upstream_port 8787;
|
|
set $upstream_proto http;
|
|
proxy_pass $upstream_proto://$upstream_app:$upstream_port;
|
|
|
|
# Only if the app holds a WebSocket open. SWAG's proxy.conf already
|
|
# sets the Upgrade headers; what it also sets is a read timeout of a
|
|
# couple of minutes, which would close every open tab's socket on the
|
|
# minute and leave the browser reconnecting for no reason.
|
|
proxy_read_timeout 86400s;
|
|
proxy_send_timeout 86400s;
|
|
}
|
|
}
|
|
|
|
## `listen 443 ssl` without `http2` is correct — `http2 on;` is set once at
|
|
## `http` scope in nginx.conf, and the `listen ... http2` parameter is
|
|
## deprecated in nginx 1.25 and later.
|